#Har bal 3.0 how to
#Har bal 3.0 series

IZotope RX4 advanced & Har-Bal 3.0 > CD Wave > AudioGate (16-44) > TLH (flac 8) Hard Dive > CD wave > adobe audition 2.0 > flac Source: audience cassette master taped by Jerry MooreДў Sony ecm 33p's > Sony tc-152 using Maxell ud-120's w/ Dolby B Har-Bal allows you to easily tidy up the sound quality of mastered or un-mastered recordings while preserving the original intent of the producer and/or recording engineer.16 bit 44.1 KHz sample rate compatible with CD burning The conventional approach is multiband compression, for which we have a disliking, mainly because to our mind it seems like a poor match to the problem at hand.

#Har bal 3.0 how to

But by selecting the time line in that manner and then controlling those errant peaks by highly selective filters that only act on the minimum amount of time required to fix the problem you end up with much better results.Д¬omplex time selection and filtering is our take on how to control errant peaks in highly dynamic instruments such as vocal parts. ItвЂ™s complex selection not because the process is complex but the selected time line is patchy and discontinuous. Any time values with peaks above the line are selected and those below are not. Instead on manually trudging through the entire time trace to find the times at where those peaks occur you would use our tool based on placing a threshold line on the peak trace. Those out of control bursts of sounds will show up as excessive peaks in the peak spectrum trace but not in the average trace as they occur rather infrequently. Imagine if you will a great recorded part of a vocal that explodes in volume on a couple of notes. That alignment canвЂ™t be accurately re-constructed with the analysis results because the spectrum resolution is reduced to 1/12th octave and the peaking and troughing of the deviate is finer scale than that. How the Air then affects spectrum then depends upon whether the peaks and troughs of the Air response line up with the peaks in the spectrum. Without the taper it would sound too bright. It is realized as a log normal random deviate applied to a unity gain all pass response with the variance of the deviate tapering at higher frequencies to add warmth. The effect the new Air has on the spectrum is actually rather small when used modestly. The ways you use it will is still the same but it will sound better and have a greater range of possibilities, one of which is stereoвЂ™ising mono sources. Har-Bal Air as it is now has been replaced with a more powerful and natural sounding Haas zone ambiance process. To get back to Left and right we use the following equations: Now the basic Har-Bal 3 filter block has left and right channels being filtered by left and right filters, then being encoded into Mid and Side using the above scheme with Mid and Side filters applied to those components and then being decoded back into Left and Right. So the level of the Side component relative the Mid component gives an indication of the stereo spread of your mix. You can see that with a mono source Side = 0 as Left = Right. Our Mid / Side decoding is defined by the following equations:

#Har bal 3.0 series

That same time series is also used to obtain the peak and average histograms in histogram view. The green is the average and the yellow is the peak. Those time series are now what you see in the timeline control above the graph in the Har-Bal UI. The new Har-Bal dynamics processing is based on the envelope information HB3 obtains during analysis: the time series constructed from peak and average power levels for each 50ms frame it analyses when a track is first opened. (Multiband compression will no longer be necessary after you realize what this tool accomplishes) ItвЂ™s an interactive process of listening and seeing and experimenting with changes. We donвЂ™t suggest you simply trust what you see and go by that. More the case that when you are struggling to hear what is wrong (but you know something is wrong) it can give visual insight. It does not mean give way to your eyes if your ears tell you everything you need.

IntuitMatch and IntuitQ вЂ“ вЂњEyes to the earsвЂќ is a more realistic slogan that we like. Loudness Compensation вЂ“ Har-Bal leaves the initial volume level unchanged even after performing spectral correction (EQ changes) thanks to its вЂњloudness compensationвЂќ algorithm. Match Loudness вЂ“ Will match your track to the perceived loudness of any commercial recording you input into Har-Bal.